Skip to comments.How do I add a second DVD drive?
Posted on 05/19/2011 7:22:01 AM PDT by MeneMeneTekelUpharsin
Can someone please give me some tips on installing my second DVD drive correctly. I have the ribbon cable end on the primary DVD RW drive and it works fine. The second DVD drive is on the middle ribbon cable connector.
The jumper on the back of the second DVD drive is on "slave". The compute recognizes the second DVD drive, but I cannot play a DVD in that drive. Any media player I run and try to "open" the movie on the second DVD drive does not "see" it. Any suggestions?
I don't care one way or the other but consistency in naming conventions always makes things easier.
Forgot how to get to “Device Manager”. Still looking... (old Fuddy Duddy here).
Found it. Cancel that...
Okay...now instead of having a problem with one CD-ROM drive, I’ve deleted both of them. Going to restart and see if the Wizard finds both of them and assigns them properly. Will let you know (if I ever make it back).
First thing I need to know is the O/S
Typically when you add a device the system will recognize it and attempt to install the appropriate driver, you need to tell it to look at the CD I assume came with the device.
Once you have installed it look at the list of devices in DM and see that the correct model devices show up. Double click on the new device and look at properties, make sure it has the correct characteristics of the device there.
Going back to another post, I would ask did you replace a precious device (CD rom) The posters are correct, if the cable has the twist in the leads going to the second position then cable select or Auto will be best. If you had a previous device installed, you may need to remove it from the list in Device Manager to remove and confusion on the O/S part the features this device represents to it
Let me know if this helps
As mentioned in another post, control panel (XP) computer management, storage management will list all available devices. It will assign the next device number to this drive, you can change it there in the future should you need to.
Second thing: Make certain that the connection to the drive is enabled in the BIOS. This may also give you an additional way to change the order of the two drives.
Third thing: Check the Master/Slave settings on BOTH drives. If you want this (presumably newer) drive to be the primary drive, make it the master and change the older drive to the slave setting.
OS is XP. Deleted both CD-ROMs from Device Manager and restarted. Put DVD in top drive (F?) and it recognizes it. Put DVD in bottom drive (G?) and it does not recognize it, although “G” shows up on the list of drives. It asks me to place a disk in drive “G”. So, I put it in the top drive (F?) and it recognized it. So, is the computer seeing the primary top RW drive as both “F” and “G”. Pulling hair out.
Are you sure the new DVD drive actually works? It could be defective.
Try temporarily replacing the old drive with the new drive. Make sure the jumper setting on the new drive is the same as the old drive, and then move the data cable from the old drive to the new drive. If the new drive works, then you know it's a configuration issue.
Finally, you might have to reconfigure your DVD player software (or other software that uses the DVD drive) to access the new drive. Some software might not check for changes once it's installed.
Thanks for everyones’ help. Won’t recognize the second drive. Don’t know why. It appears to be working, green light on, slave setting. It just can’t see the DVD in there. May be defective.
If you have another IDE slot on your motherboard for harddrives, try getting another ribbon cable and plugging the end plug into your second drive. You can try a different ribbon cable and see if that works, but if you swap the drives (set up the Master as slave and slave as master) and you get the same result, then it is your bios program.
I think your motherboard is seeing the DVD drive, but you are not passing data.
That, and it is windows...so it normally never works with anything, anyway!!
I went Mac and will never go back, precisely for this reason!
It is possible that you have a bad cable, bad drive, bios problem or combination. If you install only the drive that you are having a problem with, does it work?
Did you follow the directions that came with the second DVD drive and use the install disk?
Sounds like a codec problem if the drive lights up and you see both in explorer.
Primary and secondary are already used in reference to the controllers and each controller can support two devices.
Hence primary master and primary slave are the two devices on the primary controller, secondary master and secondary slave are on the secondary controller.
I can’t believe I am the first.
ARE YOU LOGGED ON?
Thank you, Thank you, Thank you, I’ll be here all week- try the Veal~!
You said ribbon cable, so I’m assuming you have an IDE device.
First thing to verify is that the device shows up in your BIOS. If you don’t see it in the POST, Windows won’t see it either. You may need to go into your bios and make sure you have primary/secondary slave/master enabled. Usually you can just set all 4 to auto-detect. If the bios settings are ok, then verify jumpers on BOTH drives. Either set both to auto (CS- cable select) or one to master and one to slave.
That should be all it takes, and Windows will assign it a drive letter automatically.
Ribbon cable? Good god, man! That went out with B&W television!
Master/Slave or both CS. If that’s not working then swap drive positions on the cable. If this still doesn’t work then it should tell you if the cable is bad or the drive is bad or your computer needs an update. That’s not a bad idea. If it’s old, see about upgrading the bios in it.
New dvd writers are $20. Stay away from flea markets.
Couldn't that be construed as racist talk?
Yeah, and we can’t use the terms “Male” and “Female”; as that could be considered insulting to all the fags. Instead, we must now use the terms “Plug” and “Receptical”.
However, I don’t support the Thought Police, or the PC crowd. The terms are what they are. Male/Female, and Master/Slave .... they need to put on the Big Boy Pants and quit being a bunch of snivelling sodomites.
ARE YOU LOGGED ON?
Better yet - ARE YOU LOGGED ON AS ADMINISTRATOR?
WinXP can allow all actions as an Admin to any login, but won't allow physical changes. Just a thought. Good luck.
You were right. Found another CD-Rom drive in the house and installed it. It works. Thanks to everyone. Free Republic rocks, it absolutely rocks. No other place where I feel like I can talk to family and actually get truthful answers.
Disclaimer: Opinions posted on Free Republic are those of the individual posters and do not necessarily represent the opinion of Free Republic or its management. All materials posted herein are protected by copyright law and the exemption for fair use of copyrighted works.