Skip to comments.Upcoming Pinewood Derby event set to break world record
Posted on 08/30/2010 11:57:35 AM PDT by SZonian
SANDY -- Boy Scouts are going to be very excited when they see the huge track being built for a special Pinewood Derby race to be held Saturday at Rio Tinto Stadium. It's not just the biggest track in Utah, it's the biggest ever.
For the first time, the race wasn't only for Boy Scouts -- registration was open for anyone race, and everyone is invited to watch.
The Pinewood Derby track will be more than 325 feet long when it's done, and it's going to break a world record.
World's Longest Pinewood Derby
Saturday, August 28 9:00 a.m. to 5:00 p.m. Cost: FREE to spectators Rio Tinto Stadium 9256 South State, Sandy Usually the derby tracks that engineer Steve Atkinson builds are 30 to 40 feet long. At 10 times that size, "It's easily the longest I have worked on," he said.
(Excerpt) Read more at ksl.com ...
Super Pinewood Derby Race.
My scouts would have loved to race on a track that size. Go Scouts!
I’m waiting for the Federal No Fun Commission to put a stop to this.
AWESOME. So if the track has no limits, does that mean the cars don’t have weight limits?
Now THAT would be awesome.
Did you not do the wind tunnel tests on your car before optimizing the weights?
Then there are the bearing surfaces. Did you not wear in your axles and bearings with graphite?
Then to check did you not apply at least 7 coats of hand applied lacquer sanding between each with final sanding with 2000 grit paper before before wax polishing?
For more info and videos of Saturday’s race
Don't forget to sand off the edges of the wheels where the plastic mold contact spot is too.
As to weight, it's best put over the front axle.
Just helped by son build one last year, in fact.
Ever heard of the Golden Turtle award. Slowest car to make it all the way to the end of the track. Used to be involved with pinewood derby’s through the YMCA Indian Guides. There was one group in Toledo that had a roped off area at the end of the track for Grandparents. They were served hot dogs, chips, and drinks by Dads in Tuxedos. Pretty funny. Lots of good memories.
My Pinewood Derby car was awesome. My dad did a great job.
... speed limits “expected” to reach 120 mph!
We used vertical fins to help keep it straight and keep the wheels from dragging on the center guide.
Where I come from the Pinewood Derby race is only for cub scouts.
LOL, the Pinewood Derby has been the bane of my existence for the past three years. Everytime I think “this is finally the year” me and my son have a real fast car, only to once again find ourselves solidly in the middle of the pack....oh well, next year is going to be THE YEAR!
Here is some advice:
Put your axl’s (really just nails in the BSA Kit) pointy end first into your drill, get some emory cloth (black sandpaper) and get it wet, turn your drill on and get the ribs near the top of your nail smoothed off, also sand hard against the top of the nail, on this inside, the part that will touch the wheel. Let’s say your wheel spins for 12 seconds before sanding, afterwards it will spin for over a minute, that means way, way less friction. Then, if your pack allows it use the black graphite, there’s lots more too it, my sons always finished very high, two years ago my son one the big trophy, first out of 66 drivers.
One of the Packs here in WA state used to have an UNLIMITED division for the adults.
Same adult used to win year in and year out (Boeing engineer). One year, guy used rocket motors and won.
We had an adult only, no holds bar Pine Wood Derby a few years ago in our ward.
It was a total blast!
I didn’t even come close to winning. There are several good engineers in our neighborhood. ;-)
WOW! I remember this from 1958!
My son still has the collection of Pinewood racers on his shelf. The troop had a very fancy track that had electronic timers for the speed (to 1/1000 of a second).
I wrote a software application that kept track of the times, averaged the scores and put the winners in order. Before that we slogged through the scores with calculators, which took a lot of the fun out of it.
Our Cubmaster made a car with a wireless spy camera on it. We would send it down the track just after the racing cars started and show the in car camera on a projector. One car was so slow, it got rear ended by the camera car.
I remember taking my son to the Post Office to weigh his pinewood derby car.
We had one of our Indian Guides show up with a car that was wayyyyy overweight. The kid and his Dad got out a cordless drill and started drilling holes in the car. When it got legal it looked like swiss cheese as it was painted white. It actually did quite well.
We had one Dad show up with his son’s car in a padded case. That car won hands down, and we knew there was no way the son had anything to do with the construction. The next year we instituted a rule that the kid had to carry the car back to the start of the track for the second heat (we ran 2 heats because we could only handle 2 cars at a time like a drag strip). That year the same car in the padded box showed up. When the son was carrying it back to the start, he dropped it and it broke into many pieces. The Dad spilled his drink.
True, the “Official” derby is. However, there are still many dads who are still Cubs at heart and having an “open” class is fun and helps to build comraderie and friendships.
Run the Cubs’ cars first, for the “Official” race and then have your open races. Nothing wrong with that.
Besides, I don’t know if this track even meets the official criteria, but it would be fun nonetheless.
Usually, when we’ve had “open” races, there were no restrictions of any kind. A free-for-all. Fun times, cool cars, etc.
I need to see that. I had to resist the urge to meddle with my son’s construction of his car when he was a Cub.
That’s why I always advocated an “open” race after the official derby.
That allowed the dads to build and race their own cars. Helped to cut down on dad built cars for the Cub races.
Have to spin the axles at about 10000 rpm to see if they are straight. We were allowed to select as many axles as we wanted so we did reject a few as out of line.
Then you need to polish the axles. Abrasive powder for final stone polishing put in a rag and then spin the axles again in the polish.
Then its time to apply the graphite.
We have open class races too, my daughter loves them, all my kids race in the open class.
Hey..... my day was 30 years ago. I wrote it up pretty well for one so long removed.
You are benefiting from us pioneers who established the methods decades ago. :)
But....as always, Free Republic gets to the nitty gritty by collectively giving the lesson.
You did a good job. That was fun back in the day wasn’t it.
Disclaimer: Opinions posted on Free Republic are those of the individual posters and do not necessarily represent the opinion of Free Republic or its management. All materials posted herein are protected by copyright law and the exemption for fair use of copyrighted works.